Hello, thanks for your replies! Indeed, the Windows 95 cd-roms were not bootable. To clarify, I was using a Windows 98 emergency boot disk just to get myself into MS-DOS and do the drive formatting I needed to do, then used MS-DOS to copy the installation files from my Windows 95 disk and was able to run setup from there. Errors that occur while Windows 95 is loading or prevent Windows from loading may be caused by issues in the win.ini or the system.ini. These issues can often be resolved by restoring a backup of the win.ini and the system.ini. Below are steps that can be taken to restore a backup of these files. Exit to an MS-DOS prompt. Windows protection error messages A protection error will occur when the operating system has trouble loading or unloading a virtual device driver (VxD). These drivers may be Windows files. Windows protection errors typically manifest themselves during startup with a message saying, “While Initializing devicename a Windows protection error occurred,” or you may simply see a generic.
After getting into SETUP,for Win 95, I get 'Error 0013. Setup could not create files on your startup drive and cannot set up Windows. If you have HPFS or Windows NT file system you must create an MS-Dos boot partition. If you have LANtastic server or SuperStar compression, disable it before running setup'.
I ran FDISK, have active primary partition, and formatted C drive. I tried this a few times but keep getting the same results.
Any help would be appreciated.
Thank you
Jan 12, 2019 Now that your Hardening Problem is solved, this is a new issue, therefore a new thread. We need to see a complete VBox.log, from a complete VM run. Start the VM from cold-boot (not from a paused or saved state) / Observe problem / Shutdown the VM (force close it if you have to).; With the VM completely shut down (not paused or saved), right-click on the VM in the VirtualBox Manager. Rem - by windows setup - c:windowscommandmscdex.e xe /d:tsycd1 /l:z I think these 3 files are the extent of the listings for autoexec and config on my root directory. Believe it or not, the power in my neighborhood went out due to high winds just as I was writing the last entry down last night and I didn't have time to confirm it this morning. Aug 21, 2013 The first four affected files are in various Versions of Windows 95. NTKERN.VXD: 999, 1132, 1351 and 1387. 1400 and above are OK. IOS.VXD: 999, 1132, 1351, 1387 and 1400. Long story short, I'm having trouble getting DosBox (Running Windows 3.1) to recognize.iso files I have mounted using Virtual Clone Drive. Here is what I have tried: Mounting.iso in VCD, running Dosbox and just mounting d as d: Mounting.iso in VCD, running Dosbox and mounting d as d: with '-t cdrom' on the same command line. Make sure you have selected Windows 95 at startup:. Do not use more than 32Mb of RAM: Make sure the Enable VT-x/AMD-V is deselected.
Explorer is the default Windows shell, unless a different application is configured as the shell (listed in the shell= line in the System.ini file), and loads automatically when the operating.
The first time I started it, I get a Windows protection error while initializing device NTKERN. The second time I started it in safe mode I had a windows protection error while initializing device IOS. My Dell runs at 1.8 Ghz, is it just a clocking issue?
After looking at the bootleg file, there were three devices that failed to load- setver.exe, ndis2sup.vxd, and lcd.ttf.
Win 95 Dosbox
In this article, we will examine step by step how to fix the Protection Error error for Win95 virtual machine running on the Oracle VM VirtualBox virtualization program.
How to Fix Windows Protection Error
If you encounter this error when installing Windows 95, an older operating system, using the Oracle VM VBox virtualization program on the VM, the solution to this fault is quite simple.
After completing the installation of Win 95 on VirtualBox, you will see a mistake “While initializing device OS: Win Protection Error. You need to restart your computer.” failure when the setup restarts the virtual machine to finish the last steps.
This fault can often be due to incompatible hardware drivers, unsupported hardware, or startup apps.
Windows 95 Pre Installed Dosbox
For VM Protection Failure resolution, we will fix this problem by turning off VT-x from the VM settings.
In our previous article, we did a step-by-step Win 95 installation using Oracle VM VBox.
How to Repair Boot Error in Win 95/98/2000
Dosbox Windows 95 Windows Protection Error Device Download
Dosbox Win95
When you look at the image below, you will be able to see this error better. This error causes a boot error when you want to use the Win95, Win98 or Win2000 operating system with Oracle VM VBox. Because, according to today’s operating systems, virtualization programs are being developed.
Step 1
First, completely shut down the Win 95 VM. Click X (Close) to close the VM and select Power off the machine option in the Close VM window that opens and click the OK button.
Step 2
Click the Right Key / Settings on Windows 95 from the VirtualBox VM partition. In the Windows 95 settings window, first, click System and in the right pane, on the Acceleration tab, clear the Enable VT-x / AMD-V checkbox against Hardware VT-x and click the OK button.
Step 3Toyota engine block casting numbers for sale.
When you reboot the Win 95 VM, you will see this error resolved. As a result, check the Enable VT-x / AMD-V option when you encounter this error when running older Microsoft operating systems on VT-x programs.
Final Word
In this article, we have fixed the Win 95/98/200 Boot Error that we encounter when installed Windows 95 with Oracle VM VBox. Thanks for following us!
Related Articles
Dosbox Windows 95 Windows Protection Error Devices
Dosbox Windows 95 Online
Dosbox Windows 95 Online
♦ How to Fix Screen Resolution on Win 95/98 in VBox
♦ How to Run Windows 7 in VirtualBox on Windows 10
♦ How to Run Windows 98 on Windows 10
♦ How to Create a New VM in Oracle VM VirtualBox
♦ How to Install VirtualBox on Ubuntu 17.10